My friends! I’m sharing an awesome set of paper flowers I made for a wedding table backdrop. I adore this bold combo of colors! It’s the same design as the last pink and gold set, but just different colors. Makes it look totally different!
So sweet! The table was used to hold bouquets, card box, bubbles, and the Polaroid for everyone to take a picture in front of the flowers. The pictures were added to cardstock for the guests to sign next to their pictures. Such an adorable idea!
The following pictures show the back of the stand. Even though it’s not what clients see, it’s still important to keep it neat back there.
Introducing my new feet! The previous ones seen in my diy stand video were too long. They were easily tripped on if clients removed the table and used the backdrop for pictures. Even in the Ninjago backdrop pictures you could see the legs extend past the table. No bueno! Now with these shorter bad boys, the stand is still sturdy and versatile.
Here’s one I know most of you are curious about. The flowers are not pinned to the curtain. They droop and face down when they’re pinned. So, I hot glue them to a foam board that’s cut to the right shape. When the white curtain is behind it all, you don’t even notice the foam board! . . . The foam board is hanging on the bottom of the stand in this picture just while I organize and adhere the flowers. Once I’m done it goes to the top half of the stand.
That’s that, folks! I hope you enjoyed today’s late night post. Until the next project ❤
Don’t forget to like and share my FB page! I appreciate everyone that has done so.
It’s a Lego #Ninjago Birthday Party!!! If you follow my Facebook page then you’ve seen the teasers I’ve been leaving 😉
I used the 6x7ft PVC stand I put together. Purchased 3 yards of Walmart’s basic polyester fabric and sewed each end to fit around the pipe. The Ninjago eyes are cut from a basic yellow poster and the eyes are cut from black felt. They’re sticking onto the fabric with Velcro. I, of course, put in a few stitches in each Velcro square to secure it onto the fabric.
CRICUT TIP: I googled Ninjago eyes HD to get a cleaner JPEG image. Directly under the search bar click on TOOLS then SIZE appears under that. Click on LARGE. Right click and “save image as” a picture that has high-resolution (1000+). When you feed this into #CricutDesignSpace it will clean up very nicely. It will give you amazingly cleaner edges than a regular image grab.
I watched a few dozen videos on YouTube to figure out the balloon columns. There isn’t another PVC pipe in there! It’s all held together with curling ribbon. It’s very sturdy!
The banner above only says “birthday” because the table directly to the left says “happy”.
Hope y’all enjoy today’s share! Don’t forget to get on my Facebook page where you’ll see bonus pictures/videos 👍
Very happy Sunday folks! I Miss all of your faces ❤️
Below is a video I shared on my Facebook page (I post bonus projects on that feed). I made a backdrop stand out of PVC pipes. It actually worked! #PinterestSuccess 😆
Here is the end result!!! It all came together perfectly.
The flowers are attached to 3 separate white foam boards. The matte side, not the shiney side! You can’t tell because it all blends in with the white curtains. I did that so the flowers wouldn’t sag from just being pinned with a safety pin. Now they lay flat and don’t tear into the curtain. Which I broke out the sewing machine and sewed a sheer curtain on top of an opaque curtain so I can fit them both over one pipe.
I also decorated and personalized their baptism candles. One 3×8 and one 2×8 candle.
Thanks guys for visiting my page! Don’t forget to like, comment, and share. Visit my FB page for more crafty posts that you might not see here!
I’m leaving you with this awesome picture of the Mariachi band with the flowers in the background ❤️ Blessed Sunday!
Happiest of Saturdays to everyone! I hope everyone had an awesome food & family filled Thanksgiving ❤️ I’m 6 hours south from home visiting family. But, I didn’t forget about you guys!
I’ve got another themed birthday party for you. With a video! I love this colorful Mexican Cantina theme. I made a set of bright paper flowers for the dessert table backdrop.
Please enjoy the video! Like & share ❤️
Happy Saturday friends! I love today’s project 🤗 there’s a video to enjoy!
It was an outdoor Beauty & The Beast themed birthday party for my God-daughter. I made a cake table decoration and a photo frame.
I used a yellow trifold display board. I printed images on cardstock, colored them in with Copics and Sharpies, and fussy cut them. I freehanded and painted in the “Be Our Guest”. These are my first paper roses! I love them.
The photo frame is also cut from a red trifold display board. Colored another set of images and made a small flower to go along with the theme. The letters are also fussy cut. The handsome model is my husband, Jerry ❤️
Please enjoy this awesome clip I’ve put together. The photo frames are gaining popularity. Please share any photo frames that you’ve made! See you next Saturday 😘